June 20, 2022
Fujitsu Components America

Fujitsu Introduces Wirepas Mesh 2.4 GHz Wireless Modules (Americas)

Small footprint options allow for flexible mesh network design

SUNNYVALE, Calif. – June 20, 2022 – Fujitsu Components America today launched the FWM7BLZ22x series of Wirepas Mesh 2.4 GHz embedded wireless modules to meet the increasing need for flexible mesh network designs.

The series includes three models:

FWM7BLZ22W (Sink):

The Sink, which interfaces between the router nodes (Anchors) and gateway software, is controlled by a host CPU using Wirepas Dual-MCU API via USB or UART.

FWM7BLZ22P (Anchor):

For positioning applications, the Anchor functions as a router node for location detection and can operate in standalone mode or be managed by the host CPU using UART. A USB option will be available at a later date.

FWM7BLZ22T (Tag):

The tag is used for positioning applications. A non-router node, the Tag indicates the data for the location of moving objects being tracked. It works in standalone mode or can be managed by the host CPU through UART. A USB option will be offered at a later date.

FWM7BLZ22 series

FWM7BLZ22 series

All modules in the series are powered by Nordic Semiconductor’s nRF52833 SoC, feature an embedded Mesh 2.4 GHz stack from Fujitsu partner Wirepas, which boasts low power consumption from a wide voltage range of 1.7 to 3.6V. The Wirepas Mesh 2.4 GHz architecture can accommodate changes to data transmission routes locally in the network environment, such as device failures and increases or decreases in the number of devices. The architecture also allows for easy deployment of small or large-scale decentralized systems and supports wireless remote firmware upgradeability (OTAP).

With dimensions of 7.5 x 7.9 x 1.7 mm, the small footprint requires a minimal mounting area on the PCB. An enhanced output power of +8dBm enables potential transmission range extension, while strong resistance to radio interference—a feature of Wirepas Mesh 2.4 GHz—allows higher-density installation to seamlessly work with existing nodes. There are no embedded antennas, maximizing the flexibility of electrical and housing designs to meet end-users’ requirements.

The modules can be used with existing Fujitsu mesh network products. Key applications include asset management, sensor networks, and smart lighting, just to name a few. Samples are available now, and orders for all three models will be accepted immediately.

Technical features:

  • High performance Nordic nRF52833 SoC (ARM Cortex-M4, 512 kB Flash, and 128 kB RAM embedded)
  • Embedded Wirepas Mesh 2.4 GHz stack
  • Host interface: USB or UART
  • Operating Voltage: 1.7 to 3.6V
  • Operating temperature: -40 to +85 degree C
  • Output Power: +8 dBm, Rx Sensitivity: -96 dBm
  • External antenna for most flexible system design
  • Built-in crystal (32 MHz and 32.768 kHz)
  • Dimensions: 7.5 x 7.9 x 1.7 mm

About Fujitsu Components America

Fujitsu Components America, Inc. markets and distributes electronic and system components and sub-systems throughout North and South America. Products include relays, touch panels, thermal printers, wireless modules, and input and pointing devices. The company is headquartered at 350 Cobalt Way, M/S 160, Sunnyvale, CA 94085. For product information, contact FCAI via telephone at +1-800-380-0059 or by email at For more information, please see:


Press Contact:
Julie Ritzer Ross
Phone: 1-973-943-5331

All trademarks or registered trademarks are the property of their respective owners. The prices, specifications and service details of the products listed on the pre-release are as of the announcement date. It is subject to change without notice.

Share this page

  • instagramで共有